I've tried several coding debounces I found on the internet and haven't had much luck with them, though I'll admit I felt a little in over my head, and again, the regular encoder read code was the one that gave "best" results.

I found that using the Raspberry Pi Pico, than a simple 0.1uF (ceramic) to ground on all three signal wires was enough to get them to work reliably. But using an interrupt is a must. The KY-40 includes pull up resistors so no need to add any extra ones. It looks like @jugglebug00 system is the same because of the 5V input. The only reason for that is to act as a source of voltage for the internal pull up resistors. So remove R1 to R5 from that circuit you posted.

I tried your demo code and library on this encoder and I got the same terrible results: -1, 0, -1, -2, -3, -4, -3, -2, -3, -2, -1, 0, -1, 0, -1, 0, -1, -2, -1, -2, -3, -4, -3, -4, -3, -4, -5, -6, -5, -6, -5, -4, -5, -6, -7, -8, -9, -10, -11, -12, -13, -12, -11, -12, -13, -14, -13, -14, -13, -14, -15, -14, -13, -14, -15, -14, -15, -14, -15, -16, -17, -16, -15, -14, -13, -12, -13, -12, -11, -10, -11, -10, -11, -10, -9, -8, -9, -8, -9, -10, -11, -10, -11, -12, -13, -14, -15, -16, -17, -16, -15, -16, -15, -14, -13, -12, -13, -14, -15, -14, -15, -16, -17, -16, -15, -14, -15, -16, -17, -18, -19, -20, -21, -22, -21, -22, -23, -22, -23, -22, -23, -22, -23, -24, -25, -26, -27, -26, -27, -28, -29, -28, -29, -28, -27, -26, -27, -26, -25, -26, -27, -26, -27, -28, -27, -28, -27, -26, -27, -26, -27, -26, -25, -24, -23, -22, -21, -22, -23, -24, -25, -26, -25, -24, -23, -22, -23, -22, -23, -22, -21, -20, -21, -22, -21, -22, -23, -22, -23, -24, -25, -24

I'm thinking, between my apparent poor choice in hardware and my lack of deep understanding of the coding, I may be getting out of my depth and may just try a more tried and true encoder unit or I may try a hardware filter solution if I want something less finicky.

I get "better" results with the basic encoder code. I'm beginning to think these units are the problem. I've tried so many coding solutions and the best results are still finicky. Any suggestions for a very small quality encoder?

If you can dedicate two interrupts to be used by the rotary-encoder you can use the NewEncoder-library from user gfvalvo

Below is a long-winded alternate version of the lookup table method. It enables only one interrupt at a time, so most bounces don't trigger interrupts at all. Anyway, you might give it a try to see if it makes any difference. It sends the current count to the serial monitor along with the number of interrupts which have occurred since the last detent, which ideally should be 4 or 2 depending on the type of encoder you have.

Papan Konverter MDAS 2258273 2258274 untuk GE CT, You can get more details about from mobile site on m.alibaba.com.

I did try this circuit and, like the software solutions, it didn't seem to have much positive effect. 5bd5030ac672e030391f92ff1600×1066 38 KB

Do keep in mind that the purpose of the tutorial was to illustrate that you don't need to debounce a rotary encoder. The code illustrates what I wanted to show but it is imperfect. The issue is you can get close to1kHz from a rotary encoder without much difficulty if you turn it fast enough. I think the serial prints in the demonstration code are enough to disrupt the reading as you found. Is my code reliable if you turn the encoder slowly?

Here is my code and I included both the regular encoder read code(//commented out) and the debounce code. Which doesn't decrease and actually slowly increases as the encoder glitches upward.

@StefanL38 's advice to use a library is probably best. If you still have problems after that then I suspect you have something else wrong.

GE MRI. Delivery Time: 7-10 Working Days. वारंटी: 90 days. Shipment: DHL Fedex UPS TNT. MOQ: 1 PCS. P/N: 6300216. Guangzhou Dike Electronics Scientific ...

It's possible your encoders are so bad that they won't work well with anything. The state table method generally works very well, even with encoders that bounce a lot. But if the switches in the encoder continue to bounce long after they should have settled down, there may be no way to produce good results. I've had good results with the KY-40 modules.

Items found searching CT (brand GE), apparecchio Lightspeed Ultra: 32. Sub ... 2375741 - 4/8 Slice MDAS PCI Dip LightSpeed Ultra - CT. 2404393 - 16 Slice ...

I have pretty good luck with just putting 0.1uF ceramic caps from the A, B and SW terminals to ground to do hardware debounce. Wire the commons to ground and the A,B and SW terminals to inputs set to pinMode INPUT_PULLUP.

I did try your code and wasn't able to get it working: (RIGHT TURN)-2, -1, 0, -1, 0, -1, 0, -1, -2, -3, -2, -3, -2, -1, 0, 1, 0, 1, 0, -1, 0, -1, 0, -1, 0, 1, 0, 1, 0, -1, 0, -1, 0, 1, 2, 1, 2, 3, 2, 1, 0, 1, 2, 1, 0,(LEFT TURN) 1, 2, 3, 4, 3, 4, 3, 4, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 11, 10, 9, 10, 9, 8, 7, 8, 7, 8, 9

5135265 CRADLE STEEPING MOTOR CLUTCH 1700 ASSY Positioning GT 5135265-2 CRADLE STEEPING MOTOR CLUTCH 1700 ASSY RoHS Positioning GT 5133504 CRADLE LOCK-1700 ...

I read about a hardware solution with something called a Schmitt Trigger, but could only find that available in a giant 14 pin chip and I'd like to try and keep my project small. Seemed a little overkill to debug one small component.

Mit dem Drehregler für Ihre Arduino-Anwendung können Sie verschiedenste Einstellungen im Fingerumdrehen durchführen Der Drehregler ist aus Metall und kann

: 2294300-22 · : scp3ボード · メーカー: ge · Modality: closed mri 3.jpg 2.jpg 1.jpg.

It would be very interesting to know which exact type of microcontroller you are using. Me personally those cheap KY-40 RE work pretty good with the "standard"encoder.h-library if the code is running on Arduino Unos. But very unreliable on faster microcontrollers like the ESP8266, ESP32 or teensy

Hey there, I'm trying to get this little rotary encoder to not be so glitchy and I'm at a loss. I've had the "best" luck through basic wiring (only pullup resistors on A/B), but it's still pretty finicky getting it to land on a number you want. Has anyone had any luck with them and what method did you use to get it to increase/decrease smoothly?

Gate Command V2C Board 2209547-3 GE, Definium 8000, Discovery XR650, Innova 4100IQ. Tested Medical Equipment Spare Parts for Sale, Worldwide Shipping.

Modality: Closed MRI; Model: EXCITE HDX. Previous. GE Closed MRI 5138526-2 Driver Module. Next. GE CT bed control board GEYMS GTCB3 BOARD 5245271, 5142181, ...

... 6:55pm)•. •Source:Stellar MLS as Distributed by MLS Grid #O5430691. Redfin Estimate. Redfin has the most accurate online home estimate. $415,349. $195K since ...

VCT RECEIVER ANTENNA AND BRACKET 5131930. Tested Exchange Item Exchange. Goods sold on an Exchange basis require that Buyer return a like ...

I would recommend the Rotary Library from Encoder Library, for Measuring Quadarature Encoded Position or Rotation Signals

GE Signa MRI Bit 3 Adapter Card (Fiber Optic) (VMEBUS) Part Number: 2235744-2 · Get a Quote. REQUEST A QUOTE/CONTACT US @ (866) 530-7850.

Thank you, very enlightening. That run time discrepancy may explain why I would get better results when I isolate the encoder code and it glitches again when I try and insert the same code back in my project code.