Leggett and platt remote controlinstructions

For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.

“PRESS & HOLD” MODE:To put the remote control in “press and hold” mode simultaneously press and hold the FLAT and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash 3 times, confirming the change. Your base is now set to “Press & Hold” mode.“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.REMOTE CONTROL PROGRAMMING – 1 REMOTE TO OPERATE 1 BASE(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.HEAD UPFOOT DOWN(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

leggett and platts-cape 1.0remoteprogramming

PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.

WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and Platt remotereset

IMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and Platt remotebattery replacement

NOTEREMOTE CONTROL REQUIRES (2) AAA SIZE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.

The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.

292-0073-A EDR 16438 12/22© 2022 Leggett & Platt, Inc. Adjustable Bed GroupREMOTE CONTROL FUNCTIONLOCK BUTTONTo lock / unlock the remote control buttons, press and hold LOCK button for 5 seconds. Backlight will flash 3 times.UNDERBED LIGHT BUTTONPress to turn on/off underbed light feature.FLASH LIGHT BUTTONPress to turn flashlight ON for 15 seconds.FOOT UP/DOWN BUTTONPress and hold to raise or lower the foot section.FLAT BUTTONPress to lower the base to the level position. This button also turns off massagers.HEAD UP/DOWN BUTTONPress and hold to raise or lower the head section.ZG (ZERO GRAVITY) BUTTONPress to adjust the base to the factory default ZG position. To reprogram, adjust the base, massage, and underbed light to the desired position, press and hold the FLASHLIGHT button for 6 second (remote control backlight will flash), then press the ZG button within 2 seconds. The adjustable bed will beep confirming this change. NOTEREMOTE CONTROL REQUIRES (2) AAA SIZE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.“PRESS & HOLD” MODE:To put the remote control in “press and hold” mode simultaneously press and hold the FLAT and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash 3 times, confirming the change. Your base is now set to “Press & Hold” mode.“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.REMOTE CONTROL PROGRAMMING – 1 REMOTE TO OPERATE 1 BASE(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.HEAD UPFOOT DOWN(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.

NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and platt remote controlreplacement

WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.

(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.

FOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett&Platt remotenot working

MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.

(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.

(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation.

(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.

HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.

HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and Platt remoteapp

SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.

CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and platt remote controlprogramming

Your email address will not be published. Required fields are marked *Comment * Name Email Website Save my name, email, and website in this browser for the next time I comment.

NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.

If the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Your adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.

(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…