Your adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.

(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).

Definition of hotline noun in Oxford Advanced American Dictionary. Meaning, pronunciation, picture, example sentences, grammar, usage notes, synonyms and ...

POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Kit ComponentsCMF/CMF2 80 PG Convertible 75 to 65 KBTU/H Input Conversion Kit:Main Burner Orifices (One Natural Gas Orifice and One Propane (LP) Gas Orifice)Conversion Kit Label (four overlay labels)Installation Instructions for firing rate conversionCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner Orifices (One Natural Gas Orifice and One LP GasOrifice)Conversion Kit LabelLP AccessoriesInstallation Instructions for firing rate conversionCMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelInstallation Instructions for firing rate conversionCMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion  Kit:Oil Burner NozzleConversion Kit LabelBurner HeadInstallation Instructions for firing rate conversionProduct Usage InstructionsBefore Starting the ConversionPrior to starting the conversion process, ensure that you have all the necessary components included in your specific kit. Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off the Gas to the Appliance:Set the thermostat to OFF or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move it to OFF. DO NOT FORCE THE LEVER.Please refer to the detailed Installation Instructions provided with your specific kit for step-by-step guidance on converting the firing rate of your CMF/CMF2 80 PG Series Furnace. It is important to follow all instructions carefully and to have the conversion kit installed by a qualified professional in accordance with local  codes and ordinances to ensure proper installation and avoid any safety hazards or damage to the equipment.For Model Series CMF2/CMF 80-PG Convertible and CMF2/CMF 80-PO Convertible FurnacesImportant: Read all instructions before starting the installation.WARNING: This kit must be installed by a qualified installing agency and in accordance with local codes and ordinances. Failure to properly install the conversion kit as described herein may damage the equipment and/or the home, can create a fire or asphyxiation hazard, violates U.S. listing requirements, and will void the warranty.FOR YOUR SAFETYWHAT TO DO IF YOU SMELL GASDo not try to light any appliance.Do not touch any electric switch; do not use any phone in your building.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.If you cannot reach your gas supplier, call the fire departmentGeneralThis conversion kit can be used to change the rated firing rate (input) of your CMF/CMF2 80 convertible furnace (either PG or PO) from the factory set rate of 75,000 BTU/H. The input can be either increased to 85,000 (CMF: 90,000) BTU/H or decreased to 65,000 BTU/H with the appropriate conversion kit. This set of instructions assumes that you are familiar with and have the Installation Instructions delivered with the CMF/CMF2 furnace. Before Starting the Conversion First check your kit components to ensure that all of the necessary items are enclosed. The components of each kit are listed below: CMF/CMF2 80 PG Convertible 75 to 65 KBTU/H InputConversion KitMain Burner OrificesOne Nat. Gas OrificeOne Propane (LP) Gas OrificeConversion Kit Label (consists of four overlay labels).NOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion  FURNACE NAMEFURNACE MODEL 65 PG 65 PO 90 PG 90 POCMF2710670710671710672710673CMF155941155942155943155944Table 1. Conversion Kit Label NumberCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

Coin Cell batteries are most commonly used for low-power devices such as watches, pocket calculators, key fobs, etc.

Leggett and Platt remotereset

For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.

(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.

Table 1. Conversion Kit Label NumberCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.

MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.

Locking hinge is included and keeps drawers securely in place even in moving vehicles. ... Although the dividers are not compatible with Durham small parts ...

The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.

NOTEREMOTE CONTROL REQUIRES (2) AAA SIZE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.

IMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

CMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and platt remote controlinstructions

Specifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

If the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.

HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

F. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Remove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea Level

SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett&Platt remotenot working

D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

WARNING: This kit must be installed by a qualified installing agency and in accordance with local codes and ordinances. Failure to properly install the conversion kit as described herein may damage the equipment and/or the home, can create a fire or asphyxiation hazard, violates U.S. listing requirements, and will void the warranty.

FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.

C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.

C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Leggett and Platt remotebattery replacement

Leggett and platt remote controlprogramming

WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

FOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Braeburn 1020NC Thermostat for Conventional Heating Systems and Heat Pumps. Manual (User Manual, Installation, Wiring). Check it below or download here.

Please refer to the detailed Installation Instructions provided with your specific kit for step-by-step guidance on converting the firing rate of your CMF/CMF2 80 PG Series Furnace. It is important to follow all instructions carefully and to have the conversion kit installed by a qualified professional in accordance with local  codes and ordinances to ensure proper installation and avoid any safety hazards or damage to the equipment.For Model Series CMF2/CMF 80-PG Convertible and CMF2/CMF 80-PO Convertible FurnacesImportant: Read all instructions before starting the installation.WARNING: This kit must be installed by a qualified installing agency and in accordance with local codes and ordinances. Failure to properly install the conversion kit as described herein may damage the equipment and/or the home, can create a fire or asphyxiation hazard, violates U.S. listing requirements, and will void the warranty.FOR YOUR SAFETYWHAT TO DO IF YOU SMELL GASDo not try to light any appliance.Do not touch any electric switch; do not use any phone in your building.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.If you cannot reach your gas supplier, call the fire departmentGeneralThis conversion kit can be used to change the rated firing rate (input) of your CMF/CMF2 80 convertible furnace (either PG or PO) from the factory set rate of 75,000 BTU/H. The input can be either increased to 85,000 (CMF: 90,000) BTU/H or decreased to 65,000 BTU/H with the appropriate conversion kit. This set of instructions assumes that you are familiar with and have the Installation Instructions delivered with the CMF/CMF2 furnace. Before Starting the Conversion First check your kit components to ensure that all of the necessary items are enclosed. The components of each kit are listed below: CMF/CMF2 80 PG Convertible 75 to 65 KBTU/H InputConversion KitMain Burner OrificesOne Nat. Gas OrificeOne Propane (LP) Gas OrificeConversion Kit Label (consists of four overlay labels).NOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion  FURNACE NAMEFURNACE MODEL 65 PG 65 PO 90 PG 90 POCMF2710670710671710672710673CMF155941155942155943155944Table 1. Conversion Kit Label NumberCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

To Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

This conversion kit can be used to change the rated firing rate (input) of your CMF/CMF2 80 convertible furnace (either PG or PO) from the factory set rate of 75,000 BTU/H. The input can be either increased to 85,000 (CMF: 90,000) BTU/H or decreased to 65,000 BTU/H with the appropriate conversion kit. This set of instructions assumes that you are familiar with and have the Installation Instructions delivered with the CMF/CMF2 furnace. Before Starting the Conversion First check your kit components to ensure that all of the necessary items are enclosed. The components of each kit are listed below: CMF/CMF2 80 PG Convertible 75 to 65 KBTU/H InputConversion KitMain Burner OrificesOne Nat. Gas OrificeOne Propane (LP) Gas OrificeConversion Kit Label (consists of four overlay labels).NOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion  FURNACE NAMEFURNACE MODEL 65 PG 65 PO 90 PG 90 POCMF2710670710671710672710673CMF155941155942155943155944Table 1. Conversion Kit Label NumberCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

Leggett and platt remote controlreplacement

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Your email address will not be published. Required fields are marked *Comment * Name Email Website Save my name, email, and website in this browser for the next time I comment.

Nat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea Level

(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation.

PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.

Leggett and Platt remoteapp

LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Important: Read all instructions before starting the installation.WARNING: This kit must be installed by a qualified installing agency and in accordance with local codes and ordinances. Failure to properly install the conversion kit as described herein may damage the equipment and/or the home, can create a fire or asphyxiation hazard, violates U.S. listing requirements, and will void the warranty.FOR YOUR SAFETYWHAT TO DO IF YOU SMELL GASDo not try to light any appliance.Do not touch any electric switch; do not use any phone in your building.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.If you cannot reach your gas supplier, call the fire departmentGeneralThis conversion kit can be used to change the rated firing rate (input) of your CMF/CMF2 80 convertible furnace (either PG or PO) from the factory set rate of 75,000 BTU/H. The input can be either increased to 85,000 (CMF: 90,000) BTU/H or decreased to 65,000 BTU/H with the appropriate conversion kit. This set of instructions assumes that you are familiar with and have the Installation Instructions delivered with the CMF/CMF2 furnace. Before Starting the Conversion First check your kit components to ensure that all of the necessary items are enclosed. The components of each kit are listed below: CMF/CMF2 80 PG Convertible 75 to 65 KBTU/H InputConversion KitMain Burner OrificesOne Nat. Gas OrificeOne Propane (LP) Gas OrificeConversion Kit Label (consists of four overlay labels).NOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion  FURNACE NAMEFURNACE MODEL 65 PG 65 PO 90 PG 90 POCMF2710670710671710672710673CMF155941155942155943155944Table 1. Conversion Kit Label NumberCMF/CMF2 80 PG Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Main Burner OrificesOne Nat. Gas OrificeOne LP Gas OrificeConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.LP AccessoriesInstallation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 65 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Installation Instructions for firing rate conversion.CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H Input Conversion Kit:Oil Burner NozzleConversion Kit LabelNOTE: Appropriate conversion kit label should be chosen based on the furnace model (see Table 1). Overlay the conversion kit label between “PERFORMANCE DATA” and “STANDARD” of the furnace name plate label.Burner HeadInstallation Instructions for firing rate conversion.Converting the Firing Rate of the CMF/CMF2 80 PG Series FurnacesTo Turn Off Gas to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.Push in the gas control lever and move to OFF. DO NOT FORCE LEVER.WARNING: Both propane (LP) and natural gas orifices are included with this kit. Make sure you install the proper orifice, and discard the old orifices (both Nat. and LP).Orifices for CMF/CMF2 80 PG Conv.Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea LevelRemove the Burner Assembly:Follow instructions “To Turn Off Gas To Appliance.”Shut off gas supply at meter.Disconnect gas burner electric cord, gas piping to burner, and thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner assembly from unit.C. Change the Main Burner Orifice:Disconnect the two wires leading to gas control valve.Remove three (3) fasteners from U-shaped manifold plate and orifice assembly.Remove the main orifice and replace it with the alternate fuel orifice supplied in this kit.Reconnect the manifold plate using the fasteners removed earlier. (Refer to step D-2).Connect two wires to gas control valve.D. Reassemble the Burner into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-4).Reconnect the gas piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leads.E. Set the Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H firing rate conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation Instructions provided with furnace.Converting the Firing Rate of the CMF/CMF2 80 PO Convertible SeriesA. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.

leggett and platts-cape 1.0remoteprogramming

A. To Turn Off Oil to the Appliance:Set the thermostat to “OFF” or to its lowest setting.Turn off all electrical power to the appliance.Turn the latch and open the furnace door.B. Remove the Burner Assembly:Shut off the oil supply at the tank.Disconnect electric cord, oil piping & thermostat leads.Remove three (3) fasteners holding burner in place.Remove burner from furnace.C. When Converting the CMF/CMF2 80 PO Convertible Furnace to 85,000 BTU/H (CMF: 90,000 BTU/H)Note: the Burner Head will Need to be Replaced.For CMF/CMF2 80 PO Convertible 75 to 85/90 KBTU/H conversions, remove the burner head from the oil burner & replace it with the head in the kit. (See the Replacement Parts List for description of burner head).D. Remove the Oil Nozzle and Replace it with the Nozzle from the KitFurnaceInputNozzleHeadBTU/HCMF2CMFCMF2/CMF65,000.50 GPH, 080, AF3F0CMF285,000.65 GPH, 080, AF3–CMF90,000.65 GPH, 080, B–F3HE. Reassemble the Burner Assembly into the Furnace.Reposition the burner back into the furnace and secure with three (3) fasteners removed earlier. (Refer to step B-3).Reconnect the oil piping to the burner making sure of no leaks.Reconnect electric cord and thermostat leadsF. Set Blower Speed & Check Appliance Operation:Open the electric box underneath the vestibule divider on the left-hand side of the furnace. To do this remove the single screw in the center of the plate.The blower speed must be set to the one associated with the firing rate change. Connect the low-speed blower wire (red) for 75 to 65 KBTU/H conversions. Connect the high-speed blower wire (black) for 75 to 90 KBTU/H firing rate conversions.The kit has two labels included with it. The first label must be applied over the corresponding portion of the rating label. Align the label such that it covers and updates the appropriate information on the rating label. The other label included in the kit must be applied over the corresponding label on the burner to update that information. If the burner & rating plate labels are dirty clean them with water and a mild detergent.Adjust the air setting of the burner as described in the “Adjusting the Burner” section of the Installation Instructions.Open the manual shut-off valve & follow the “Operating Instructions” as outlined in the CMF/CMF2 Furnace Installation InstructionsSpecifications & illustrations subject to change without notice or incurring obligations (07/23).  O’Fallon, MO, © Nortek Global HVAC LLC 2023. All Rights Reserved.10459670 (Replaces 707798D)Documents / ResourcesNortek 903102 CMF Firing Rate Conversion Kit [pdf] Instruction Manual903099, 903100, 903101, 903102, 903102 CMF Firing Rate Conversion Kit, CMF Firing Rate Conversion Kit, Firing Rate Conversion Kit, Rate Conversion KitReferencesUser Manual

3 days ago — 19 October 2024. 0. 1. Facebook · Twitter · Pinterest · WhatsApp · ReddIt · Email. Print. xxxxxlocalcluster. - Advertisement -. By Tahna Weston.

Fired at 65 KBTU/HLPNat. Gas#43#24Orifices for CMF2 80 PG Conv.Fired at 85 KBTU/HLPNat. Gas#37#18Orifices for CMF 80 PG Conv.Fired at 90 KBTU/HLPNat. Gas#36#160-2000’ Above Sea Level

“PRESS & HOLD” MODE:To put the remote control in “press and hold” mode simultaneously press and hold the FLAT and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash 3 times, confirming the change. Your base is now set to “Press & Hold” mode.“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.REMOTE CONTROL PROGRAMMING – 1 REMOTE TO OPERATE 1 BASE(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.HEAD UPFOOT DOWN(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

The Firing Rate Conversion Kit #903099, 903100, 903101, and 903102 is designed for Model Series CMF2/CMF 80-PG Convertible and CMF2/CMF 80-PO Convertible Furnaces. This kit allows you to change  the rated firing rate (input) of your furnace from the factory set rate of 75,000 BTU/H. The input can be increased to 85,000 (CMF: 90,000) BTU/H or decreased to 65,000 BTU/H with the appropriate conversion kit. Proper installation of this kit is essential for safety and to avoid damage to the equipment.

HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Find company research, competitor information, contact details & financial data for MULTIMEDICAL SRL of VIADANA, MANTOVA. Get the latest business insights ...

Your email address will not be published. Required fields are marked *Comment * Name Email Website Save my name, email, and website in this browser for the next time I comment.

PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.

Prior to starting the conversion process, ensure that you have all the necessary components included in your specific kit. Converting the Firing Rate of the CMF/CMF2 80 PG Series Furnaces

(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.

292-0073-A EDR 16438 12/22© 2022 Leggett & Platt, Inc. Adjustable Bed GroupREMOTE CONTROL FUNCTIONLOCK BUTTONTo lock / unlock the remote control buttons, press and hold LOCK button for 5 seconds. Backlight will flash 3 times.UNDERBED LIGHT BUTTONPress to turn on/off underbed light feature.FLASH LIGHT BUTTONPress to turn flashlight ON for 15 seconds.FOOT UP/DOWN BUTTONPress and hold to raise or lower the foot section.FLAT BUTTONPress to lower the base to the level position. This button also turns off massagers.HEAD UP/DOWN BUTTONPress and hold to raise or lower the head section.ZG (ZERO GRAVITY) BUTTONPress to adjust the base to the factory default ZG position. To reprogram, adjust the base, massage, and underbed light to the desired position, press and hold the FLASHLIGHT button for 6 second (remote control backlight will flash), then press the ZG button within 2 seconds. The adjustable bed will beep confirming this change. NOTEREMOTE CONTROL REQUIRES (2) AAA SIZE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.“PRESS & HOLD” MODE:To put the remote control in “press and hold” mode simultaneously press and hold the FLAT and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash 3 times, confirming the change. Your base is now set to “Press & Hold” mode.“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.REMOTE CONTROL PROGRAMMING – 1 REMOTE TO OPERATE 1 BASE(1) Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.HEAD UPFOOT DOWN(2) Unplug the base from the power outlet. Wait 3 minutes, then plug base back into power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE. NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(3) Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release.HEAD DOWNFOOT UP(4) Operate the remote control to verify the base functions correctly.REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES(1) Plug both bases into power outlet. Operate each base to verify the base functions properly.Lower both bases to the flat position. NOTEIF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE).(2) UNPLUG both bases. Place both bases on their sides close to each other. CAUTIONDUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.(3) Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.SYNC PORTSYNC CABLEBASE 1 CONTROL BOXBASE 2 CONTROL BOX NOTECONTROL BOX APPEARANCE AND SYNC PORT LOCATION MAY VARY.(4) Turn both bases over onto their legs. CAUTIONMAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.(5) Plug both bases back into power outlet.  NOTEAN ELECTRICAL SURGE PROTECTION DEVICE IS RECOMMENDED (NOT INCLUDED).(6) Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare. NOTETO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE SYNC CABLE FROM CONTROL BOXES.POWER DOWN OPERATIONYour adjustable base, depending on model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.(1) Insert (2) 9-volt alkaline batteries into the power brick. POWER BRICKBATTERY COMPARTMENT DOOR(push in and slide up to remove)INSTALL (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDED NOTEBATTERIES (NOT INCLUDED) ARE GOOD FOR ONLY ONE USE.(2) Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.ELECTRICAL POWER CORDPAIR BUTTONIN-LINE SWITCHFLAT(3) Remove batteries from power brick and discard. When power is restored from outage, base is ready to resume normal operation. REMOVE (2) 9 VOLT BATTERIES*BATTERIES NOT INCLUDEDTROUBLESHOOTINGIf the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:SYMPTOMSOLUTIONNo features of the base will activate.• Program the remote control (see Remote Control Programming section of this manual for programming procedures).• Unplug power cord, wait 30 seconds and plug in to reset electronic components.• Electrical circuit breaker may be tripped. Check electrical service breaker box to verify.• Defective surge protection device or electrical outlet. Test outlet by plugging in another working appliance.• If the base was operated over the rated duty cycle, thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.Remote control backlight does not illuminate.• Replace batteries in remote control.Head or foot section will elevate, but will not return to the horizontal (flat) position.• Base mechanism may be obstructed. Elevate base and check for obstruction. Remove obstruction.Excessive motor noise.• Head section may be too close to the wall.• If base is located on hard surface flooring, place carpet pieces or rubber caster cups under each leg or caster of the base.• Elevate the head or foot section a short distance (with the remote control) to realign the lift/ lower mechanisms with the base support platform.• Verify that base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.• If base is installed over a base frame, verify motors are not causing base frame (or base frame components) to vibrate.ADVISORYIMPORTANT INFORMATIONREAD THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT WARNINGFOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED).FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.ELECTRICAL RATINGInput: 100-130VAC, 50/60Hz, 1.5A. Output: 29VDC, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.WARRANTY WARNINGDo not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment.SERVICE REQUIREMENTSService technicians are not responsible for moving furniture, removing headboards and footboards or any items required to perform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motor operation does not exceed two (2) minutes over a twenty (20) minute period, or approximately 10% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.UL (Underwriters Laboratories) recognized components.CFR 1633 approved for use with most mattresses.SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.HOSPITAL USE DISCLAIMERThis base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.MASSAGE OPERATIONThe massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.FCC COMPLIANCEThe equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.Radio Frequency = 2.4GHz.Documents / ResourcesSimplicity EDR 16438 Leggett Platt Remote Control [pdf] User GuideEDR 16438 Leggett Platt Remote Control, EDR 16438, Leggett Platt Remote Control, Platt Remote Control, Remote Control, ControlReferencesUser ManualRelated PostsLeggett Platt 7 Button Remote Control User Manual7 Button Remote Control user guide CUSTOMER SERVICE toll free: (800) 888-3078 292-0042-D EDR 16028 4/21 © 2021…Remote Pro NiceHome FILO 400 Remote InstructionsRemote Pro NiceHome FILO 400 Remote Program NiceHome FILO Remote (Mode 1) Remove the cover of the motor…Handy Remote Control InstructionsHandy Remote Control Instructions Handy Remote Control Smart Touch Control  Leggett Platt LP Adjustable Bed Control App User GuideLeggett Platt LP Adjustable Bed Control App User Guide BEFORE BEGINNING Refer to the Adjustable Base Setup Guide…

Axiom Family Counseling Services, Inc. Logo. Axiom Family Counseling ... We are located at 3 Kensington Square, New Kensington PA 15068 . Part time ...

“PRESS & RELEASE” MODE:To revert back to “press and release” mode, simultaneously press and hold the LOCK and FLASHLIGHT buttons for 3 seconds. Remote backlight will flash once, confirming the change. Your base is now set to “Press and Release” mode.NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

3D Printing Filaments made out of Premium PLA, PLA/PHA, CO-POLYESTER AND SPECIAL composite materials. all filaments are available in Fabulous Colors.

Custom Wheel Accessories does it's best to provide as much information as possible to help with the applications of Wheel Adapters. · Hub Studs CANNOT protrude ...

Briggs & Stratton 6179 Maintenance Kit for 10-13KW Standby Generator. Designed for the 10-13KW Standby Generator.