Your email address will not be published. Required fields are marked *Comment * Name Email Website Save my name, email, and website in this browser for the next time I comment.

16 Jul 2011 — Those ladders top out at about 15 feet, and if one were made to reach 20 feet it looks like it would be over 40 pounds. Yersmay1 | Jul 17, 2011 ...

Prime Part Source (PPS) is an industry leader in OEM automotive part sales. We partner with organizations who alter or customize new, zero mile vehicles ...

MOUNT HEAD ASSEMBLYRefer to Figure 9. WARNING: Al though compact the drill press head assembly is heavy. Two people are required to mount the drill press head onto assembly the column.Slide drill press head assembly onto top of column.Position head so that it is centered over base.Secure head by tightening the set screws (Ref. No. 36) on the right side of the head casting.MOUNT QUILL FEED HANDLE ASSEMBLYRefer to Figure 8.Place key (Ref. No. 32) into key way of pinion (Ref. No. 33).Place quill feed handle assembly (Ref. No. 34) over pinion.Secure handle assembly with tap screw (Ref. No. 36) and plate (Ref. No. 35).Thread quill feed knob (Ref. No, 37) onto quill feed handle assembly.INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDS

TOOL SHOULD BE MAINTAINEDAlways unplug tool prior to inspection.Consult manual for specific maintain­ing and adjusting procedures.Keep tool lubricated and clean for safest operation.Remove adjusting tools. Form habit of checking to see that adjusting tools are removed before switching machine on.Keep all parts in working order. Check to determine that the parts will operate properly and perform their intended function.Check for damaged parts. Check for alignment of moving parts , binding breakage, and mounting or any other condition that may affect a tool’s operation.Any damaged parts should be proper­ly repaired or replaced. Do not perform makeshift repairs.(Use parts list provided to order repair parts.)KNOW HOW TO USE TOOLUse right tool fo rjob. Do not force tool or attachment to do a job for which it was not designed.Disconnect tool when changing drill bit or cutter.Avoid accidental start-up. Make sure that the tool is in the OFF position before plugging in.Do not force a tool. It will work most efficiently at the rate for which it was designed.Keep hands away from moving parts and cutting surfaces.Never leave tool running unattend­ed. Turn the power off and do not leave tool until it comes to a com plete stop.Do not overreach. Keep proper foot­ ing and balance.Never stand on tool. Serious injury could occur if tool is tipped or if drill bit is unintentionally contacted.Know your tool. Learn the tool’s operation, application and specific limitations.Use recommended accessories (refer to page 11). Use of improper acces­ sories may cause risk of injury to persons.Handle workpiece correctly. Protect hands from possible injury.Turn machine off if it jams. Drill¢ jams when it digs too deeply into workpiece. (Motor force keeps it stuck in the work.)All work shall be secured using either clamps or a vise to the drill press table. It is unsafe to use your hands to hold any workpiece being drilled.Feed work into a bit or cutter against the direction of rotation of bit or cutter.Use recommended speed for drill accessory and workpiece material.Keep guards in place and in proper working order. Do not operate the machine with guards removed.Always be sure the machine is securely anchored to the floor or the workbench.Make certain table locks and head locks are tightened before starting machine. CAUTION: Think safety! Safety is a combination of operator common sense and alertness at all times when tool is being used.AssemblyRefer to Figures 7 and 8. WARNING: Do not attempt to opaerate tool until it is completely assembled according to the instructions.MOUNT COLUMN ASSEMBLY TO BASERefer to Figure 7.Place base (Ref. No. 1) on flat level surface.Mount column assembly (Ref. No. 7) to base using five socket head bolts (Ref. No. 6).MOUNT TABLERefer to Figure7.Attach crank handle (Ref. No. 22) to shaft on worm gear (Ref. No. 20), rotate worm gear to remove slack and shoulder crank handle against table bracket. Secure handle with set screw (Ref. No. 21). Attach crank han­ dle knob (Ref. No. 23) to handle.Slide table (Ref. No. 13) into hole in table arm. Secure table with table locking handle (Ref. No. 11).MOUNT HEAD ASSEMBLYRefer to Figure 9. WARNING: Al though compact the drill press head assembly is heavy. Two people are required to mount the drill press head onto assembly the column.Slide drill press head assembly onto top of column.Position head so that it is centered over base.Secure head by tightening the set screws (Ref. No. 36) on the right side of the head casting.MOUNT QUILL FEED HANDLE ASSEMBLYRefer to Figure 8.Place key (Ref. No. 32) into key way of pinion (Ref. No. 33).Place quill feed handle assembly (Ref. No. 34) over pinion.Secure handle assembly with tap screw (Ref. No. 36) and plate (Ref. No. 35).Thread quill feed knob (Ref. No, 37) onto quill feed handle assembly.INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

... MA722 Bombardier DHC8Q300, reg. JA722A, on January 5, 2024. PHOTO Tadayuki YOSHIKAWAAviation Wire - 240345886 from Afloimages premium library of news, sport ...

CAUTION: Think safety! Safety is a combination of operator common sense and alertness at all times when tool is being used.

Refer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:

WARNING: For your own safety, read all of the instructions and precautions before operating tool.PROPOSITION 65 WARNING: Some dust created by using power tools con­ tain chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.Some examples of these chemicals are:

Dayton Drill Press features a heavy cast iron base, column collar, work table and head. Work table height is adjustable using rack and pinion. Table can be tilted 45 both right and left, and rotates 360 on a vertical axis. Work table surface is precision ground which features T-slots for secure, accurate mounting of work­ piece and a coolant trough. Digital readout displays spindle depth and RPM. Other  features of the Dayton drill press are an enclosed ball bearing quill assembly, quickbelt change and tension mechanism, positive quick-adjust feed depth stop and a 1 HP, 1725 RPM motor. A chuck and chuck arbor are included. Dayton drill press are ideal for use in home shops, maintenance shops and light industrial applications. Spindle speeds are adjustable for drilling steel, cast iron, aluminum, wood and plastic.

KNOW HOW TO USE TOOLUse right tool fo rjob. Do not force tool or attachment to do a job for which it was not designed.Disconnect tool when changing drill bit or cutter.Avoid accidental start-up. Make sure that the tool is in the OFF position before plugging in.Do not force a tool. It will work most efficiently at the rate for which it was designed.Keep hands away from moving parts and cutting surfaces.Never leave tool running unattend­ed. Turn the power off and do not leave tool until it comes to a com plete stop.Do not overreach. Keep proper foot­ ing and balance.Never stand on tool. Serious injury could occur if tool is tipped or if drill bit is unintentionally contacted.Know your tool. Learn the tool’s operation, application and specific limitations.Use recommended accessories (refer to page 11). Use of improper acces­ sories may cause risk of injury to persons.Handle workpiece correctly. Protect hands from possible injury.Turn machine off if it jams. Drill¢ jams when it digs too deeply into workpiece. (Motor force keeps it stuck in the work.)All work shall be secured using either clamps or a vise to the drill press table. It is unsafe to use your hands to hold any workpiece being drilled.Feed work into a bit or cutter against the direction of rotation of bit or cutter.Use recommended speed for drill accessory and workpiece material.Keep guards in place and in proper working order. Do not operate the machine with guards removed.Always be sure the machine is securely anchored to the floor or the workbench.Make certain table locks and head locks are tightened before starting machine. CAUTION: Think safety! Safety is a combination of operator common sense and alertness at all times when tool is being used.AssemblyRefer to Figures 7 and 8. WARNING: Do not attempt to opaerate tool until it is completely assembled according to the instructions.MOUNT COLUMN ASSEMBLY TO BASERefer to Figure 7.Place base (Ref. No. 1) on flat level surface.Mount column assembly (Ref. No. 7) to base using five socket head bolts (Ref. No. 6).MOUNT TABLERefer to Figure7.Attach crank handle (Ref. No. 22) to shaft on worm gear (Ref. No. 20), rotate worm gear to remove slack and shoulder crank handle against table bracket. Secure handle with set screw (Ref. No. 21). Attach crank han­ dle knob (Ref. No. 23) to handle.Slide table (Ref. No. 13) into hole in table arm. Secure table with table locking handle (Ref. No. 11).MOUNT HEAD ASSEMBLYRefer to Figure 9. WARNING: Al though compact the drill press head assembly is heavy. Two people are required to mount the drill press head onto assembly the column.Slide drill press head assembly onto top of column.Position head so that it is centered over base.Secure head by tightening the set screws (Ref. No. 36) on the right side of the head casting.MOUNT QUILL FEED HANDLE ASSEMBLYRefer to Figure 8.Place key (Ref. No. 32) into key way of pinion (Ref. No. 33).Place quill feed handle assembly (Ref. No. 34) over pinion.Secure handle assembly with tap screw (Ref. No. 36) and plate (Ref. No. 35).Thread quill feed knob (Ref. No, 37) onto quill feed handle assembly.INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Refer to Figure 1. WARNING: Be careful not to touch overheat power lines, piping. lighting, etc., if lift­ ing equipment is used. Drill press weighs up to 216 lbs. Proper tools, equipment and qualified personnel should be employed in all phases of unpacking and installation.Crates should be handled with care to avoid damage from dropping, bumping, etc. Store and unpack crates with cor­ rect side up. After uncrating drill press, inspect carefully for any damage that may have occurred during transit. Check for loose, missing or damaged parts. If any damage or loss has occurred, claim must be filed with carrier immediately.Check for completeness. Immediately report missing parts to dealer. Check for shipping damage. If damage has occurred, a claim must be filed with the carrier immediately. Check for com­ pleteness. Immediately report missing parts to dealer.The drill press is shipped unassembled. Locate and identify the following assem­ blies and loose parts:A. Head AssemblyB. TableC. BaseD. Column AssemblyE. Feed Handle KnobF. Feed HandleG. Table HandleH. Table Handle KnobI. Center Pulley Assembly Not Shown;: Drill Chuck with Key, Arbor, Drill Drift, M8 x 24 Key, Plate, M6 x 16 Tap Screw, five M10 x 40 Socket Head Bolts, 3, 5 and 8mm Hex Wrenches,. two M8 x 125 Hex Head Bolts, two M8 Lock Washers, four MS Flat Washers, and two MS Hex Nuts.IMPORTANT: Many unpainted steel sur­ faces, such as column and table top, have been coated with a protectant. To ensure proper fit and operation, remove coating. Coating is easily removed with mild solvents, such as mineral spirits, and a soft cloth. Avoid getting solution on paint or any of the rubber or plastic parts. Solvents may deteriorate these finishes. Use soap and water on paint. plastic or rubber components. After cleaning, cover all exposed surfaces with a light coating of oil. Paste wax is recom­ mended for table top. Never use highly WARNING atatte solvents. Non-flammable solvents are recom­ mended to avoid possible fire hazard.

Refer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

LARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…

Refer to Figures 7 and 8. WARNING: Do not attempt to opaerate tool until it is completely assembled according to the instructions.MOUNT COLUMN ASSEMBLY TO BASERefer to Figure 7.

Mercedes XQXX|| The all new Mercedes|| Interior||Mercedes XQXX Interior#carshorts#alonewarriorshorts.

www.avancemaquinaria.com is the best online shopping platform where you can buy Durham 9 Drawer Steel Storage Cabinet w/ Pad-Lockable Hinge 611-95 Damaged from ...

DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

Refer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.

Please read and save these instruction. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference,

2093592-001 | 1-YEAR PLANNED MAINTENANCE KIT. ... GE Appliance – Owner's Manuals and Installation Instructions. For Major Household Appliances:. Many GE ...

Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Find the top 15 cities, towns, and suburbs near Aurora, OH, like Twinsburg and Streetsboro, and explore the surrounding area for a day trip.

WARNING: Your risk from these exposures vary, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. Always wear OSHAINIOSH approved, properly fitting face mask or respirator when using such tools. CAUTION: Always follow proper operating procedures as defined in this manual even if you are familiar with use of this or simi­ lar tools. Remember that being careless for even a fraction of a second can result in severe personal injury.BE PREPARED FOR JOB

SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Eye/face wash is activated by flag handle or foot treadle. Four GS-Plus™ spray-type outlet heads deliver a flood of water over a wide area of coverage for ...

PREPARE WORK AREA FOR JOBKeep work area clean. Cluttered work areas invite accidents.Do not use power tools in dangerous environments. Do not use power tools in damp or wet locations. Do not expose power tools to rain.Work area should be properly lighted.Proper electrical receptacle should be available for tool. Three-prong plug should be plugged directly into proper­ly grounded, three-prong receptacle.Extension cords should have a grounding prong and the three wires of the extension cord should be of the correct gauge.Keep visitors at a safe distance from work area.Keep children out of workplace. Make workshop childproof. Use pad­ locks, master switches or remove switch keys to prevent any uninten­tional use of power tools.TOOL SHOULD BE MAINTAINEDAlways unplug tool prior to inspection.Consult manual for specific maintain­ing and adjusting procedures.Keep tool lubricated and clean for safest operation.Remove adjusting tools. Form habit of checking to see that adjusting tools are removed before switching machine on.Keep all parts in working order. Check to determine that the parts will operate properly and perform their intended function.Check for damaged parts. Check for alignment of moving parts , binding breakage, and mounting or any other condition that may affect a tool’s operation.Any damaged parts should be proper­ly repaired or replaced. Do not perform makeshift repairs.(Use parts list provided to order repair parts.)KNOW HOW TO USE TOOLUse right tool fo rjob. Do not force tool or attachment to do a job for which it was not designed.Disconnect tool when changing drill bit or cutter.Avoid accidental start-up. Make sure that the tool is in the OFF position before plugging in.Do not force a tool. It will work most efficiently at the rate for which it was designed.Keep hands away from moving parts and cutting surfaces.Never leave tool running unattend­ed. Turn the power off and do not leave tool until it comes to a com plete stop.Do not overreach. Keep proper foot­ ing and balance.Never stand on tool. Serious injury could occur if tool is tipped or if drill bit is unintentionally contacted.Know your tool. Learn the tool’s operation, application and specific limitations.Use recommended accessories (refer to page 11). Use of improper acces­ sories may cause risk of injury to persons.Handle workpiece correctly. Protect hands from possible injury.Turn machine off if it jams. Drill¢ jams when it digs too deeply into workpiece. (Motor force keeps it stuck in the work.)All work shall be secured using either clamps or a vise to the drill press table. It is unsafe to use your hands to hold any workpiece being drilled.Feed work into a bit or cutter against the direction of rotation of bit or cutter.Use recommended speed for drill accessory and workpiece material.Keep guards in place and in proper working order. Do not operate the machine with guards removed.Always be sure the machine is securely anchored to the floor or the workbench.Make certain table locks and head locks are tightened before starting machine. CAUTION: Think safety! Safety is a combination of operator common sense and alertness at all times when tool is being used.AssemblyRefer to Figures 7 and 8. WARNING: Do not attempt to opaerate tool until it is completely assembled according to the instructions.MOUNT COLUMN ASSEMBLY TO BASERefer to Figure 7.Place base (Ref. No. 1) on flat level surface.Mount column assembly (Ref. No. 7) to base using five socket head bolts (Ref. No. 6).MOUNT TABLERefer to Figure7.Attach crank handle (Ref. No. 22) to shaft on worm gear (Ref. No. 20), rotate worm gear to remove slack and shoulder crank handle against table bracket. Secure handle with set screw (Ref. No. 21). Attach crank han­ dle knob (Ref. No. 23) to handle.Slide table (Ref. No. 13) into hole in table arm. Secure table with table locking handle (Ref. No. 11).MOUNT HEAD ASSEMBLYRefer to Figure 9. WARNING: Al though compact the drill press head assembly is heavy. Two people are required to mount the drill press head onto assembly the column.Slide drill press head assembly onto top of column.Position head so that it is centered over base.Secure head by tightening the set screws (Ref. No. 36) on the right side of the head casting.MOUNT QUILL FEED HANDLE ASSEMBLYRefer to Figure 8.Place key (Ref. No. 32) into key way of pinion (Ref. No. 33).Place quill feed handle assembly (Ref. No. 34) over pinion.Secure handle assembly with tap screw (Ref. No. 36) and plate (Ref. No. 35).Thread quill feed knob (Ref. No, 37) onto quill feed handle assembly.INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

MOUNT TABLERefer to Figure7.Attach crank handle (Ref. No. 22) to shaft on worm gear (Ref. No. 20), rotate worm gear to remove slack and shoulder crank handle against table bracket. Secure handle with set screw (Ref. No. 21). Attach crank han­ dle knob (Ref. No. 23) to handle.Slide table (Ref. No. 13) into hole in table arm. Secure table with table locking handle (Ref. No. 11).MOUNT HEAD ASSEMBLYRefer to Figure 9. WARNING: Al though compact the drill press head assembly is heavy. Two people are required to mount the drill press head onto assembly the column.Slide drill press head assembly onto top of column.Position head so that it is centered over base.Secure head by tightening the set screws (Ref. No. 36) on the right side of the head casting.MOUNT QUILL FEED HANDLE ASSEMBLYRefer to Figure 8.Place key (Ref. No. 32) into key way of pinion (Ref. No. 33).Place quill feed handle assembly (Ref. No. 34) over pinion.Secure handle assembly with tap screw (Ref. No. 36) and plate (Ref. No. 35).Thread quill feed knob (Ref. No, 37) onto quill feed handle assembly.INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Whatever you need, we'll source the parts and deliver them to your door. Our huge list of genuine Ferrari parts is the result of our own experience owning ...

INSTALL CENTER PULLEY ASSEMBLYRefer to Figures 8 and 9.Loosen belt tension knobs (Fig. 8, Ref. No. 38) and use belt tension handle (Fig. 8, Ref. No. 43) to move motor toward front of drill press.Open cover of pulley housing (Fig. 9, Ref. No. 2) and insert center pulley assembly (Fig. 8, Ref. No. 8) into the head casting.Choose a speed from Figure 5 or the pulley housing speedchart and con­nect spindle pulley to center pulleywith front drive belt (Fig. 8, Ref. Nos. 2,7 and 8). Connect center pulley to motor pulley with rear drive belt (Fig. 8, Ref. Nos. 8, 54 and 55)NOTE: Front drive belt is type 270J4 and rear drive belt is type 300J4.Turn handle (Fig. 8, Ref. No. 43) to move motor toward rear of drill press and tighten motor lock knobs.MOUNT CHUCK AND ARBORRefer to Figure 8.Be sure spindle, arbor and chuck tapers are clean and dry. Make sure quill is completely retracted.Use the provided chuck key (Ref. No. 31) to adjust the jaws of the chuck (Ref. No. 30) until they are recessed inside the drill chuck body.Place drill chuck on a workbench face down. Arbor (Ref. No. 29) has a short taper and a long taper. Place short taper into top of drill chuck and tap with a rubber or wooden mallet.Slide arbor into the spindle (Ref. No. 24) while slowly rotating drill chuck. Spindle has a rectangular pocket in which the tang fits into. Once tang is oriented correctly, drill chuck will not rotate without turning the spindle.Tap the end of drill chuck with a rub­ ber or wooden mallet to seat it into the spindle.Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.InstallationRefer to Figures 2, 3 and 4.POWER SOURCEThe motor is designed for operation on the voltage and frequency specified.Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.Running the unit on voltages which are not within the range may cause over­ heating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.GROUNDING INSTRUCTIONS WARNING: Impro”.erconnectiont)of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to pro­tect operator from electrical shock.Check with a qualified electrician if grounding instructions are not under­ stood or if in doubt as to whether the tool is properly grounded.This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 2) for your protection against shock hazards.Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding type receptacle as shown in Figure 2.Do not remove or alterg rounding prongin any manner. In the event of a malfunction or breakdown , groundin g provides a path of least resistance for electrical shock. WARNING: Do not permit fin­minals of plug when installing or remov­ing from outlet.Plug must be plugged into matching out­ let that is properly installed and grounded in accordance with all local codes and or dinances. Do not modify plug provided. If it will not fit in outlet, have proper out­ let installed by a qualified electrician.Inspect tool cords periodically, and if damaged, have repaired by an autho­ rized service facility.Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.Where a 2-prong wall receptacle is encountered, it must be replaced with a properl y grounded 3-prong receptacle installed in a c cordance with National Electric Code and local codes and ordinances.  WARNING: This work should be performed by a qualified electrician.A tempo rary 3-prong to 2-prong grounding adapter ( See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a prop-erly grounded outlet box or a properly grounded wire system.Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician. EXTENSION CORDSThe use of any extension cord will cause some drop in voltage and loss of power.Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.Use the table to determine the mini-mum wire size (A.W.G.) extension cord.Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.If the extension cord is worn, cut, or damaged in any way, replace it immediately.EXTENSION CORD LENGTH (120 VOLTS)Wire SizeA.W.G.Up to 50 ft.1650-100 ft14100-150 ft12NOTE: Using extension cords over 150 ft. long is not recommended.EXTENSION CORD LENGTH (240 VOLTS)Wire SizeA.W.G.Up to 50 ft.1850-200 ft16200-300 ft14NOTE: Using extension cords over 300 ft. long is not recommended.ELECTRICAL CONNECTIONSRefer to Figure 4. WARNING: All electrical connections must be performed by a qualired electrician. WARNING: Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or any time wiring is inspected.The motor should be wired for 120 volts and clockwise rotation as viewed from shaft end of motor.A label on the motor describes the possible wiring configurations. There are many different possible combina-tions, so only the diagram provided with the motor should be used.The motor cord must be secured to protect the wiring connections from possible strain.The power supply to motor is con-trolled by a push button switch. Power lines are connected to the quick connect terminals of the switch.The green ground line must remain securely fastened to the motor ground terminal to provide proper grounding.To operate drill press at 240 volts, rewire motor as shown in Figure 4 and replace line cord plug with a 240 volt, 15A, 3-prong plug. If motor label has a different wiring configuration, use the motor label diagram to rewire motor.Recommended Dayton plugs, connectors and receptacles for 240 volts:20 Amps Plug 250 Volts ConnectorNEMA L6-20 Receptacle5A0815A0825A08030 Amps Plug 250 Volts ConnectorNEMA L6-30 Receptacle5A0875A0885A086OperationRefer to Figures 5-9.STARTING AND STOPPING THE DRILL PRESSRefer to Figure 8. WARNING: Be sure drill bit is not in contact with workpiece when motor is started. Start motor and allow bit to come up to full speed before drilling.The ON/OFF switch (Ref. No. 15) is located on the front of the head casting.To turn the drill press on, push green ON button. Always allow drill bit to come up to speed before drilling.To turn the drill press off, press the large red OFF paddle or lift the pad-dle and press directly on the red OFF button. Do not leave drill press until the bit has come to a complete stop.SPEED ADJUSTMENTSRefer to Figures 5 and 8. WARNING: Be sure drill press is turned off and is dis-connected from power source before adjusting speeds.To change spindle speed, loosen motor lock knobs (Ref. No. 38), turn handle (Ref. No. 43) to move the motor toward front of drill press. This will loosen the belt and permit relo-cating the belt to the desired pulley groove for the required spindle speed (See Figure 5, page 6).After belt has been repositioned, turn handle to move motor toward rear of drill press and tighten motor lock knobs.Check belt for proper tension and make any final adjustment. A belt is properly tensioned when light pres-sure applied to midpoint of the belt produces about 1/2″ deflection.TABLE ADJUSTMENTSRefer to Figure 7.Height adjustments: To adjust table, loosen locking handle (Ref. No. 18) and turn crank handle (Ref. No. 23) to desired height. Immediately retighten table bracket locking handle.Figure 5 – Spindle Speed AdjustmentRPM Belt Location138A1-5225782-52304A1-4Y344C3-5z461Apr-52497A1-3X566B2-4Y708A1-2W755C3-4Y92782-3X1491E5-4Y1660D4-3X1761C3-2W236204-2W2444E5-3X3476E5-2WRotation of work table: Loosen table locking handle (Ref. No. 18) and rotate table (Ref. No. 13) to desired position and retighten handle.Tilting work table: Loosen table bolt  (Ref. No. 10). Remove pin and nut (Ref. No. 9). To do this, tighten nut until pin slips out easily. Tilt table to desired angle up to 45° and retighten table bolt. Reinsert pin and nut when returning the table to 0° position.To obtain more distance between chuck and table, the work table can be rotated 180° and base can be used as a work surface. This permits drilling of larger objects.Clamp table securely after adjustments have been made.DEPTH STOP ADJUSTMENTRefer to Figure 8.To control drilling depth, use scale (Ref. No. 16) to adjust to desired depth. Depress and hold pin. slide depth stop nut (Ref. No. 15) along lead screw until bottom edge of nut coincides with the desired depth on the scale, then release pin. Use this feature to drill more than one hole to the same depth.MOUNT DRILL BITRefer to Figure 8. WARNING: Be sure drill press is turned off and is dis­connected from power source before mounting drill bit.Place drill bit in jaws of chuck.Tighten chuck with chuck key. Be sure to tighten chuck using all three posi­ tions on chuck body and remove key.3. Use only the self-ejecting chuck key (Ref. No. 31) supplied with this drill press, or a duplicate key. Use of any other key might allow start up with the key still in the chuck. An airborne key could strike the operator and cause injury.REMOVING THE CHUCKRefer to Figures 8 and 9.Rotate quill feed handle (Fig. 8, Ref. No. 34) until slot is exposed in the side of the quill (Fig. 8, Ref. No. 24) Lock quill in position using handle (Fig. 9, Ref. No. 30).Rotate spindle until inner slot is aligned with outer slot. You will see through spindle when slots are prop­ erly aligned.Insert the drift key (Fig. 8, Ref. No. 25) into the slots and tap lightly with hammer. The arbor and chuck will drop from spindle.DIGITAL DISPLAY PANELRefer to Figure 6.Display panel ‘A’ shows the depth of the spindle and spindle RPM.Button ‘8’ turns power on and off to Display ‘A’Button ‘C’: Press once for spindle depth in inches; press again for spin­ dle depth in mm; press once again for spindle RPM.Button ‘D’ resets display at zero for spindle depth.MaintenanceRefer to Figures 7 and 8. WARNING: Tum switch off and ]remove plug from outlet before maintaining or lubricating your drill press.Replace worn drive belt when needed.LUBRICATIONThe ball bearings are lubricated at the factory and need no further lubrication. Using 20 non detergent oil. periodi­ally lubricate the splines (grooves) in the spindle and the rack (teeth on the quill) as follows:Lower quill assembly (Fig. 8, Ref. No. 24) all the way down.Apply lubricant around the inside of the hole in the spindle pulley (Fig. 8, Ref. No. 2).Apply lubricant to rack (teeth) onquill (Fig. 8, Ref. No. 24) while extended below drill press head.Apply lubricant to rack and piniongear (Fig. 7, Ref. Nos. 8 and 19) on column and table assembly.Frequently blow out any dust that may accumulate inside the motor. If the power cord is worn, cut, or dam­ aged in any way, have it replaced immediately. For motor lubrication, follow instructions on motor plate.Troubleshooting ChartSymptomPossible Cause(s)Corrective ActionNoisy operation1. Incorrect belt tension2. Dry spindle3.Loose spindle4. Loose motor pulley1. Adjust tension2. Lubricate spindle (See Lubrication)3. Tighten pulley nut4. Tighten set screw in pulleyBit burns or smokes1. Incorrect belt speed2. Chips not coming out of hole3. Dull bit4. Feeding too slow5. Bit not lubricated6. Bit running backwards1. Change speed2. Retract bit frequently to clear chips3. Sharpen or replace bit4. Feed faster; enough to allow drill to cut5. Lubricate bit6. Check motor rotation to be sure it is clockwise facing shaft endExcessive drill runout or wobble1. Bent bit2. Bit not properly installed in chuck3. Chuck not properly installed4. Worn spindle bearings1. Replace bit2. Install bit properly3. Install chuck properly4. Replace bearingsDrill bit binds in workpiece1. Workpiece pinching bit or excessive feed pressure2. Improper belt tension3. Workpiece not supported or clamped properly1. Support or clamp work, decrease feed pressure2. Adjust tension3. Support or clamp workpiece securelySpindle does not turn1. No power to drill press2. Defective switch3. Defective motor1. Check wiring, fuse or circuit breaker2. Replace switch3. Replace motorNoisy spindleDefective bearingsReplace bearingsDocuments / ResourcesDAYTON 5PHC3B 17 Inch Floor Model Drill Press [pdf] Instruction Manual5PHC3B, 17 Inch Floor Model Drill Press, Model Drill Press, 17 Inch Floor Drill Press, Drill PressReferencesUser ManualRelated PostsPOWERMATIC Drill Press PM2820EVS Instruction ManualPOWERMATIC Drill Press PM2820EVS WARNING: This product can expose you to chemicals including lead which is known to…DANCO 62068 4 Inch Steel Floor Register Instruction ManualDANCO 62068 4 Inch Steel Floor Register Instructions Tools Required: Screw & Screwdriver (Not provided with kit) Refer…LARIN DPV-1 Drill Press Visa Owner's ManualLARIN DPV-1 Drill Press Vise SAFETY WARNINGS Study, understand, and follow all instructions before operating this device. Drill…SEALEY YKSG20 Hydraulic Floor Press Instruction ManualSEALEY YKSG20 Hydraulic Floor Press Thank you for purchasing a Sealey Jack. Manufactured to a high standard this…

Clear. Menu options. Categories; Deals · Sell · Help · Sign in or RegisterSign out ... Retail & Shop Fitting Equipment · Test, Measurement & Inspection Equipment ...

Hardware (Two M8 x 125 hex head bolts, M8 lock washers, M8 hex nuts and four M8 flat washers) has been provid­ ed for mounting the drill press to a wood base plate. This is recommended if you intend to place the drill press on a mobile base. The minimum recom­mended size of the wood base plate is 3/4 x24x24″.